Sync Cords and Interconnects - Listing: Page Bottom
As most everything on this site is a custom item, many of the things in this post also appear in other areas. Should you see something of interest, but wish it were just a little bit different, send me a note to discuss it, as many times that's where the next picture will come from!
------------------------------------------------------------------------------
A(***)Hot Shoe to ScrewLock PC Plug - Upright Mtg:
The Hot Shoe to ScrewLock PC Plug - Upright Mounting will support the CyberSync, Skyport, MicroSync, or the eBay radio transmitters without a problem, and connect to the PC jack of your camera. This is especially useful when you are using a 580EX II flash unit along with a newer camera, or you just don't want to use a separate sync cord. The Aux Collar is shown already installed on the locking collar, and the combined items of Hot Shoe and Aux Collar are $100. Should you wish to omit the Aux Collar, the Hot Shoe alone is $80, just as the other version of this item, the Vertical Hot Shoe, shown below illustrated with the SkyPort transmitter. A simple twist tie is used (in both versions) to help prevent the rotation of the hot shoe in the PC jack.B(***)Hot Shoe to ScrewLock PC Plug for SkyPort:
The Hot Shoe to ScrewLock PC Plug (Semi-Rigid) will easily support a SkyPort or MicroSync transmitter when it is locked into the PC jack of your camera. The hot shoe itself is offset from the PC jack by 1.375 inches so you will have clearance for your hand on the left side of the camera. This item is $80 and is usually used when a flash is in the camera hot shoe, and you prefer to not use a separate dangling sync cord. A similar item is seen with the hot shoe in the Upright Mounting position as seen in this link.This connection point is also needed if your on camera flash unit does not have a sync jack which can function as an OUTPUT, or you are using a 580EX II with any of the newer Canon cameras, all of which have special digital communications on the center trigger contact.
A work around device, being called the "Pre-Flash Ignore Trigger" is in testing and more of this information can be seen at the attached link.
C(***)Aux Collar for ScrewLock PC Plug:
The Aux Collar for the ScrewLock PC Plug is a custom fit collar that makes for easy turning of the small locking collar used with the ScrewLock PC plugs. This is especially useful for those wearing gloves in cold weather, or large fingers in small spaces. As each collar is custom made and fit, the specific cable does need to be sent to me, or this item can be fit to a new plug end on a new device. This Aux Collar is currently $20 each. A similar item is made for the Nikon 10 pin plug and can be seen here.D(***)Hot Shoe to ScrewLock PC Plug:
Here the Hot Shoe to ScrewLock PC Plug has been individually reinforced with wire and layered epoxy to give the connection added strength and rigidity. The hot shoe itself is offset from the PC jack by 1.375 inches so you will have clearance for your hand on the left side of the camera. This item is $105 and is usually used when a flash is in the camera hot shoe, and you prefer to not use a separate dangling sync cord. The extra support loop can be added (for no additional cost) so that a twist or zip tie can be used to add support and prevent
twisting of the hot shoe, as seen here. A similar item is seen with the hot shoe in the Upright Mounting position as seen in this link. The Aux Collar is currently $20 each. A similar item is made for the Nikon 10 pin plug and can be seen here.This connection point is also needed if your on camera flash unit does not have a sync jack which can function as an OUTPUT, or you are using a 580EX II with any of the newer Canon cameras, all of which have special digital communications on the center trigger contact.
E(***)Extra Small Sub-Mini Plug for SkyPort:
The SkyPort transmitter can be triggered from a hot shoe contact, or by a sync cord having an extra small sub-mini plug inserted into the side sub-mini jack. The upper image is an Extra Small Sub-Mini RA Plug Sync Cord, modified especially to fit the small space of the SkyPort and having a ScrewLock PC plug assembled 
on. The lower image shows the Extra Small Sub-Mini Straight Plug Sync Cord, again modified especially to fit the small space of the SkyPort. Due to the very close quarters, the straight plug is easier to grip and remove, while the RA plug presents a smaller profile. This sync cord with the extra small sub-mini plug (RA or straight) can be made up in a length up to 12 inches long for $45. Add $5 extra for lengths up to 3 feet, and $10 extra for lengths up to 6 feet. It is actually better to carefully grind the underside of the overhang of the SkyPort in a small arc to provide more room for a larger plug. If you order a sync cord, you can send me your SkyPort, and there will be no charge to adjust the underside of the SkyPort to provide for a better fitting, larger sub-mini plug.F(***)Reduced Neck Sub-Mini RA Sync for SkyPort:
The Reduced Nick Sub-Mini Plug Sync Cord is made to get into very tight spaces like the SkyPort transmitter (see the other styles just above) The pricing is the same also. This sync cord with the extra small sub-mini RA plug can be made up in a length up to 12 inches long for $45. Add $5 extra for lengths up to 3 feet, and $10 extra for lengths up to 6 feet. If you are mounting the SkyPort in a cold shoe like in the above link, this Reduced Neck Sub-Mini Plug is not even small enough, and you will have to use the format shown there. A comparison of this Reduced Neck Sub-Mini Plug and a factory molded sub-mini plug used in a 6 Foot Coiled PVC Sync Cable can be seen here.G(***)Sub-Mini Plug Camparison - Narrow Neck Mod:
The Sub-Mini Plug Comparison - Narrow Neck Mod shows the sub-mini plug that is factory molded onto the 6 Foot Coiled Sync Cable on the left. This sub-mini plug has a reduced neck, although the overall plug size is longer than the standard sub-mini plug (seen on the right). It also happens to be a 3 conductor (notice the 2 black insulator bands) sub-mini plug that can carry 2 different information channels. This was the plug and sync cord that was originally offered when the Aux Sync Jack Mod was first introduced several years ago. The standard sub-mini plug seen on the right has been custom modified to have a narrow neck to match the factory plug on the left as a way to fit into the tighter spaces that previously only the left plug could fit into. Doing this Narrow Neck Mod will add $25 to the cost of whatever this plug is being used on.H(***)ScrewLock PC Plug to RA Sub-Mini Plug:
Filed Small to Fit SkyPort Transmitter:
The sync cord (any length available) has a narrow neck RA sub-mini plug which has been filed to fit under the overhang of the SkyPort Transmitter (see images top, and bottom). The inset shows the clearance from under the overhang, even when using the standard heavyweight (3mm) cable for the sync cord. A high quality, high reliabliity ScrewLock PC plug is assembled
onto the end of the cable. This sync cord with the extra small sub-mini RA plug can be made up in a length up to 12 inches long for $45. Add $5 extra for lengths up to 3 feet, and $10 extra for lengths up to 6 feet. If you are using a cold shoe like the Stroboframe shoe shown here, then the plug has to be made extra small which will tend to make the overmolding more prone to accidental breakage. It is actually better to carefully grind the underside of the overhang of the SkyPort in a small arc to provide more room for a larger plug. If you order a sync cord, you can send me your SkyPort, and there will be no charge to adjust the underside of the SkyPort to provide for a better fitting, larger sub-mini plug.I(***)Y Sync Cord with Extra ScrewLock PC Jack:
This Y Sync Cord with Extra ScrewLock PC Jack is a hardwired insurance policy that is quick and easy to set up, relies on the reliable ScrewLock PC plugs, and has no extra splitters or adapters to get lost. The junction box has an optional ScrewLock PC jack for the expansion of this item into a 4 ended splitter. Naturally, each leg of this item can be customized on ordering to have any length of sync cord, coiled or straight, ending in just about anything you can imagine. This specific example has leg lengths of 16 feet, 16 feet, and 10 feet, and is $105 without the extra PC jack, or $150 including the extra PC jack. As an example, using standard PC plugs this item would be $90 without the extra PC jack, and $135 including the extra PC jack.J(***) Y Connector / Splitter Leica DMR Unit
This Y Connector /Splitter is made specifically to allow the AC adapter power supply, and a wired shutter control cable to connect to the Leica motor drive unit (DMR), and operate together. Normally, only one device can be plugged into the DMR unit at a time. If you want the DMR to be powered by the AC adapter for long periods of time without having to rely on the internal batteries, and use an intervalometer, or other wired shutter device at the same time, this Y Connector / Splitter is needed. All 8 conductors are wired through for a seemless operation. Due to the cost of the individual connectors, this item as shown is $200. This item can also be made using all inline connectors instead of the 2 panel mount jacks shown, currently for the same cost.K(***)
Leica DMR Power Supply: Using the same specialized 8 pin sub-mini connectors, and an appropriate AC-regulated DC power supply, a replacement power supply can be made for $90, which is about half the cost of the Leica branded power supply.L(***)
Leica DMR Wired Trigger: Using these same specialized 8 pin sub-mini connectors, and a standard wired manual tripper, a one position Wired Trigger or Remote Trigger cable (to connect to a radio receiver) can be made for $90, again about half the cost of the Leica branded Electric Release Switch Mfg #14255 (image coming soon).
M(***)
Connecting a Canon 580EX II to a SkyPort Receiver while the 580EX II is in Manual Master mode is now possible; it is just an additional $10 to add the electronics into a Hot Shoe (like this) or one ot the sync cords in this section, and all will work just fine! The hot shoe or sync cord can still also be used in a conventional manner for other radios and other flash units without a problem.N(***)
O(***) 6 Foot Coiled Sync Cable w/ Safety Clip
6 foot Coiled Sync Cable with Safety Clip: $40As shown, this cord connects from my sub-mini aux sync jack to any device using a mini plug, such as the Pocket Wizard radio transmitter. The Safety Clip helps to prevent both plug pullout and breakage of the plug / jack combo, as well as reducing the strain on the cable. The long gently coiled cord is especially helpful to allow keeping the PW in a pocket along with an external battery pack, as an example. This sync cable can replace the normally included Standard Weight 16 inch Sync Cord for $20. (RA mini plugs are not suggested with the longer coiled cords, as this puts an extra bend in the end of the cable where it enters the radio unit.)
P(***) Standard Weight Sync Cord
This is the Standard Weight Sync Cord 16 inches long that I use for all the Aux Sync Jack Mods that use the sub-mini jack in the device (flash units, Off Camera Cords, ST-E2, etc). One cord is INCLUDED with each mod done, and one additional cord can be purchased for $10. Additional cords are $15 each. Custom, longer lengths add $5, and different plug ends are also an extra $5. The 6 foot Coiled Sync Cord (shown above) can replace this straight cable for $20.Q(***) Shortened RA Sync Cord
This Shortened RA Sync Cord is a standard weight sync cord for use with the Aux Sync Jack Mods (flash units, Off Camera Cords, ST-E2, etc), but the straight mini plug has been replaced with a RA mini plug, and the length has been shortened to the specs as requested by the photog. This is available for $20 in lengths up to 24 inches, and an additional $5 for lengths to 48 inches.R(***) Lightweight Coiled Sync Cord
The Lightweight Coiled Sync Cord will stretch to over 16 inches, and retracts to about half that length. It is available as shown for $25, or in a custom length version up to double the length shown for $40. Different plug ends are also available for an extra $5.S(***) Custom Sync Cord (Coiled Rubber)
This Custom Sync Cord (Coiled Rubber) is shown with a RA mini plug on one end, and a straight mini plug on the other. The ends both exit the coil axially for a very smooth extension and retraction of about a 3:1 ratio of the coiled section. The cord will gently stretch to just over 10 inches, and fully retract repeatedly. This high quality cord is $45 as shown, in lengths up to a 6 inch coiled section (approximately 22 inches extended). The longest coiled section currently available is 14 inches, which will result in about a 6 foot extended length of cord for $65. Various other connector ends in 2 and 3 conductor styles are available (just ask). Below is an example of a longer cord with different connectors, tail length and coiled length.T(***)Custom Long Sync Cord (Coiled Rubber):
This version of the Custom Sync Cord (Coiled Rubber) is a longer version than shown just above, has a straight mini plug on eash end, short 2 inch tails, and 10 inches of relaxed rubber coils, all at the specific request of the photog who ordered it this way. This rubber coiled cable has 2 high quality conductors plus a full shield to minimize RF interference issues. The rubber stays flexible in a very wide temperature range, extends in about a 3:1 ratio, and retracts to the relaxed length repeatedly. Three conductor, and other end connectors are also available. This high quality cord is $55 as shown. The longest coiled section currently available is 14 inches, which will result in about a 6 foot extended length of cord for $65.U(***) Dual Linked Sync Cord
This Custom Dual Linked Standard Sync Cord will connect 2 aux sync jack modified flash units into a single PW (Pocket Wizard) or other trigger device. As shown with the straight mini plug at 12 inches, this item is only $35. A RA mini plug is optional for $5, (see Dual Linked Sync Cords, below) and the length of each sub-mini plug length can be customized as needed for an extra $5 up to 24 inches, and an extra $10 to extend the length to 6 feet. Add additional sub-mini plugs going into the mini plug for $15 each. This is similar to the Dual Linked Hot Shoes to RA Mini Plug for flash units that don't already have the Aux Sync Jack. Any other sync cord can be connected in a similar fashion, by combining 2 (or 3) sync cords into a single connector. The final price of the custom cord is usually the total of the price of each cord, less one straight mini plug; or just ask!V(***) Triple Linked Sync Cord
The Triple Linked Sync Cords is for connecting 3 flash units to a single PW or other radio unit. The leg lengths and plug type are all customizable to your needs. Each of these examples have leg lengths of 8 inches, 8 inches, and 12 inches. Pricing for the left sync cord (2 ScrewLock PC plugs, 1 sub-mini plug) is $30 + $25 + $20 = $75, while the right sync cord (3 sub-mini plugs) is $25 + $20 + $15 = $60. Longer length legs will be slightly additional.W(***) Dual Linked Sync Cord (Short)
Here is another example of the Dual Linked Sync Cords ending in mini jacks, showing a standard off the shelf Y splitter ending in the straight mini plug on the left and a custom Y splitter ending in a RA mini plug on the right. The standard off the shelf version is just $10, while the custom version, in leg lengths up to 12 inches would be $35. The custom version is shown with red and white mini jacks, although all black are also available upon request. Using one of these splitters, in combination with 2 Hot Shoe Adapters will work the same as the Dual Linked Hot Shoes.(***)
PC Plugs - Standard and ScrewLock to Mini
X(***) Lightweight PC Sync Cord
This Standard Lightweight PC Sync Cord is $10 by itself, or can be included with the Aux Sync Mod for the 580 EX II for no additional cost. It is about 10 inches long.Y(***) Heavyweight Standard PC Sync Cord
The Standard Heavyweight PC Sync Cord is $20 in custom lengths up to 24 inches, and $25 for custom lengths up to 15 feet. Different plug ends are also available for an extra $5.Z(***) ScrewLock PC Plug to Inline Mini Jack
This ScrewLock PC Plug to an Inline Mini Jack is $40 as shown, and $35 without the Safety Clip and Shock Absorbing Coils. For cameras and flash equipment that allow the use of the ScrewLock PC Plug (both Canon and Nikon), this is a much improved version of the standard PC Plug, in that the center pin is spring loaded off center, and the outer collar screws into the body of the PC jack to hold the PC plug securely in place for a positive uninterrupted electrical contact. The drawback here is that it holds too tightly, and needs to be unscrewed to be removed, which can't be done in rapid fashion. If the cable is subjected to a shock load, the plug will not come out, and the camera or flash could possibly fall to the ground! By having the Inline Mini Jack, Shock Absorbing Coils, and Safety Clip (attached to the camera strap mounting ring), any shock load or pull on the cable will cause the normally secure Mini Plug to come unplugged from the Inline Mini Jack, with the Safety Clip being attached to the camera strap anchor, and the stress being absorbed by the short coiled section of the flexible rubber cord.ZA(***) Long Coiled PC Sync Cord
The Long Coiled PC Sync Cord is $40 for custom lengths up to 5 feet, and $45 for lengths up to 15 feet. The Safety Clip is included (or can be left off if you prefer), to help prevent both plug pullout and breakage of the plug / jack combo, as well as reducing the strain on the cable. Different plug ends are also available for an extra $5.ZB(***) Long Coiled Sync Cord - ScrewLock PC Plug
The Long Coiled Sync Cord with the ScrewLock PC Plug is $50 and is made of a very flexible rubber (not the usual PVC) and thus extends very easily and retracts reliably (approximately 3:1 ratio). This cord can be shortened for no additional cost, and a RA mini plug can be added instead of 
the straight mini plug for just an additional $5, as seen in the second image. The Safety Clip is included (or can be left off if you prefer), to help prevent both plug pullout and breakage of the plug / jack combo, as well as reducing the strain on the cable. You can add a mini plug / mini jack disconnect close to the ScrewLock PC plug for $25 to make this a snap apart safety cable as can be seen in the Sync Cable just below.ZC(***)Long Coiled ScrewLock Sync Cord w/ Disc
Here is the Long Coiled ScrewLock PC Rubber Sync Cord with the Disconnect and Safefy Clip, and is $75 as shown for the 2 sections. This cord is made of the high quality rubber jacketed cable for long term use. The Safety Clip is included (or can be left off if you prefer), to help prevent both plug pullout and breakage of the plug / jack combo, as well as reducing the strain on the cable. The disconnect helps to reduce the strain on the ScrewLock PC jack of the camera.ZD(***) ScrewLock PC Sync Cord - RA Mini Plug
This ScrewLock PC Sync Cord to a RA Mini Plug is $30 for up to a 10 inch long cord (normal 8 inches). Add $5 for lengths 11 to 36 inches, $10 for lengths 37 inches to 10 feet. This cord can be made with the standard PVC jacket, or the more flexible urethane rubber jacket for $40. (The rubber jacketed cords are in shorter supply, and are not usually available as a straight cord longer than 10 inches.) Longer custom lengths will have a coiled section seen above in the Long Coiled Sync Cord - ScrewLock PC Plug. To make this cord ending in a straight mini plug would be $5 less. This 10 inch RA-RA Sync Cord works especially well when mounting the PW to the flash head using the PW Caddy as seen here. To use this type of sync cord with the SkyPort Transmitter, the sub-mini plug must be used, and then ground to a very small size, as seen in these SkyPort Sync Cords, starting at $45. The Aux Collar can be added as an aid in turning the locking ring for $20 each, and is seen here.ZE(***) Inline Mini Jack to PC Plug Long Tip
The Inline Mini Jack to PC Plug Long Tip Tapered Sync Cord is $40 and is shown along with the Standard Weight 16 Inch Sync Cord, which is $15, but is included with any Aux Sync Jack Mod. The tapered long tip (see inset image to compare with the standard PC plug) will fit into the standard PC jack, but it will also fit the newer Hasselblad CF, T-Star, and Bronica cameras without doing damage to the small O-ring inside the PC jack.(***)
Misc Adapters, Connectors, Cables
ZF(***) Mini-DIN Extension Cable
This Mini-DIN Extension cable is used with matching mini-DIN connectors in extending the length of the Off Camera Cords with mods. It is available in black as 6 ft: $30, 10 ft: $33, 15 ft: $35, 20 ft: $38, 25 ft: $40, 50ft: $65, 100 ft: $85, and in tan 50 ft: $50, 100 ft: $60.ZG(***) RA Mini Plug to HH Male Plug
RA Mini Plug to HH (Safety Cover & Wein adapter are not included) . This sync cord is available for $25, with custom length and different plug /jack ends as needed. The
safety cover adds $5. The second image shows a HH plug where the blades are non-polarized (both blades are the same size). Again, this cord is available in custom lengths and is usually $25.ZH(***) Manual Tripper on 6 Foot Coiled Cable
This Manual Tripper on a 6 foot Coiled Cable Ending in a Mini Plug is $50. The image also shows 2 optional adapters: Mini Jack to HH Male, and Mini Jack to HH Female. Each adapter is $25, and can be made as a short 6 inch cable instead of a rigid adapter for
the same price. The same Manual Tripper is also available ending in a HH outlet (male or female) which can be put in place instead of the the mini plug for just $5. If you are using the "Add-A Tap" setup with zip cords, be sure to specify that you need UNPOLARIZED HH plugs which have both blades of the same width.ZI(***) Manual Tripper Comparison
The Manual Tripper Comparison shows the difference in size of the two types of Manual Trippers now available. Each is priced at $50 with either a 6 foot staight or coiled cord, and will end in a straight mini plug. A short coiled cord, and a RA mini plug are optional for $5 each. A Safety Clip can be put on the cable end near the mini plug for just $5. The Small Manual Tripper has a low force actuator that provides a good tactile feedback, and can be actuated by a vertical press, or a press in almost any other direction as well, while the Large Manual Tripper is a silent non-tactile switch that is acutated in a vertical direction only. The length and diameter of the Small Manual Tripper lends itself to being taped to almost anything, while the Large Manual Tripper is easier to hand hold.ZJ(***) Manual Tripper in Vinyl Hand Grip
This image shows the Manual Tripper Set into a Vinyl Hand Grip. It is $50 as shown with a molded mini plug on a 6 foot cable. Other styles of switches, grips, connectors, and cables are available as needed. The vinyl hand grip is hollow and was originally made to fit on the control stick of an ultra-light plane, so the pilot could take pictures without letting go of the control stick. Different diameters are available to fit over different size tubes, or the vinyl grip can be just hand held just as it is.ZK(***) Manual Tripper in Plastic Box
Here is the Manual Tripper Set into a Plastic Box. It is $50 as shown with the 6 foot cord and molded straight mini plug, although other switch styles, and box sizes are available. The box is supplied with heavy duty Velcro for mounting, and the cable length and exit position, as well as the switch position can be customized.ZL(***) Barrel Connector
The coupler on the left is also called a Barrel or Gender Changer for $10, as it will connect 2 mini plugs together. If only one plug is inserted, the plug will now have the change of gender, hence the name. On the right is a Mini Jack to PC Plug Adapter for $40.ZM(***) ScrewLock PC Plug to Mini Plug Adapter
This custom ScrewLock PC Plug to Mini Plug Adapter will only allow a roll movement along the long axis of the connector. It is about 1.25 inches long, and is $50 as shown. There is no difference in price to use a sub-mini plug (2.5mm) instead of the mini plug (3.5mm) shown. The same adapter using a standard PC plug instead of the ScrewLock PC plug would be $40.ZN(***) ScrewLock PC Plug to RA Mini Plug Adapter
Another form of rigid connector is the ScrewLock PC Plug (RA) to Sub-Mini Plug Adapter. This item is also about 1.25 inches long and is $50 as shown. There is no difference in price to use a mini plug (3.5mm) instead of the sub-mini plug (2.5mm) shown. The same adapter using a standard PC plug instead of the ScrewLock PC plug would be $40.ZO(***) ScrewLock PC Plug to Mini Jack Adapter
Here is another rigid connector using the ScrewLock PC connector: the ScrewLock PC Plug (RA) to Mini Jack Adapter. This item is about 1.5 inches long and is also $50 like the other adapters above. There is no difference in price to use a sub-mini jack (2.5mm) instead of the mini jack shown. The same adapter using a standard PC plug instead fo the ScrewLock PC plug would be $40.ZP(***) ScrewLock PC Plug vs Standard PC Plug
This image shows a comparison bewteen the different PC connectors: ScrewLock PC Plug vs Standard PC Plug in a Rigid Adapter ending in a Sub-Mini Plug. The adapter with the ScrewLock PC plug is about 1.25 inches long, while the adapter with the standard PC plug is slightly shorter at just over 1.0 inch. The Standard PC Plug Adapter is $40, while the ScrewLock PC Plug Adapter is $50. There is no difference in price to use a mini plug (3.5mm) instead of the sub-mini plug (2.5mm) shown.ZQ(***) Nikon SC-18 Connecting Cord
The Nikon SC-18 Connecting Cord (Customer Supplied) can be converted to a Pocket Wizard Cable for $20 (connects into the SC-17 3-pin port). I have a limited supply of the SC-18 plug and cord for the mod for $40 additional.ZR
Here is the same Nikon SC-18 Connecting Cord that has been converted to a Pocket Wizard Cable, ending in a RA mini plug for $25. The SC-18 (or SC-19, or SC-30) cable is usually customer supplied, but I often have several of the SC-18 cables in inventory that I can supply for $40, in a length up to 24 inches.ZS(***) Mini connector Extension Cables
Mini Connector Extension Cables (the mini size is also known as 3.5mm or 1/8 inch) are available in set lengths, and different combinations of plug ends: 6 ft: $15, 12 ft $20, 25 ft: $25, 50 ft: $45, 100 ft: $55. Add $5 to cut one of these cables to a custom length, or to use a different connector (except PC connectors, which are shown below).ZT(***) 6 Foot Dual Coiled Cable
The 6 foot Dual Coiled Cable is actually 2 isolated sync cords coiled together and costs $65. Ending in 2 color coded mini plugs, this cable is most often used with the Lens Mounted Dual Switch Trigger Cable. The other end of the cable can either be the RJ11 plug / RJ45 coupler combination, or the optional 4 conductor mini plug (see inset) which is an additional $5.ZU(***) Coiled Cables
Coiled cables can have many different connector ends, and lengths. These can be used as the set lengths below, or cut apart to make a cable of a completely different length and type. The Coiled Mono 1/4 inch (RA Plug to Straight Plug) in the upper left of the picture is currently available in 12 feet for $20, and 25 feet for $25. The Coiled Mono 1/4 inch (RA Plug to RA Plug) in the upper right of the picture is available in lengths of 25 feet for $25. The Coiled Stereo 1/4 inch Extension Cable (Straight Plug to Inline Jack) in the lower right of the picture is also available in lengths of 25 feet for $25. The Coiled Stereo Mini Extension Cable (1/8 inch Straight Plug to Inline Jack) in the lower left of the picture is available in lengths of 10 feet for $20, and 15 feet for $25. Add $5 to cut one of these cables to a custom length, or to use a different connector (except PC connectors).ZV(***) Long Tip PC Plug vs Standard PC Plug
This image show the comparison between the Long Tip Tapered PC Plug and the Standard PC Plug. The tapered plug is also gold plated for improved conductivity, and will fit in the standard PC jack, but it will also fit the newer Hasselblad CF, T-Star, and Bronica cameras without doing damage to the small O-ring inside the PC jack.ZW(***) USB UltraFlex Extension Cable
A USB UltraFlex Extension Cable (M/F) with a covered boot in a length of 10 feet is available here for $25, while the 6 foot version is $20 and a 3 foot version is $15. The FireWire 4 Pin Cable (M/M) is available in a 15 foot cable for $35, a 10 foot cable for $25, a 6 foot cable for $20, a 3 foot cable for $15, and a special 25 foot heavy duty cable (not shown) for $45 as in the 2 images below (click either to enlarge):
The USB Extension Cable (left image) is used as an inline disconnect and extension for the Mini-USB Port Extension, while the FireWire 4 Pin Cable (right image) is also used as an inine disconnect and extension for the FireWire Port Extension, as seen in these links.ZX(***)FireWire Cables
ZY
ZZ
ZZA(***)USB Cables
ZZB
ZZC
------------------------------------------------------------------------------
Sync Cords and Interconnects - Complete Listing
As most everything on this site is a custom item, many of the things in this post also appear in other areas. Should you see something of interest, but wish it were just a little bit different, send me a note to discuss it, as many times that's where the next picture will come from!
------------------------------------------------------------------------------
RA Sub-Mini, Mini Plugs - For Use with My Aux Sync Jack Mods
Coiled Rubber Sync Cable - Custom Length
Coiled Rubber Sync Cable - Long Length
Coiled PVC Sync Cable - 6 Foot
Coiled Sync Cable - Short
Dual Linked Sync Cords
Standard Weight 16 Inch Sync Cord
RA Sub-mini Plug to RA Mini Plug
Triple Linked Sync Cords - Custom Size & Config
PC Plugs - Standard and ScrewLock
Coiled Sync Cord - PC Plug to Straight Mini Plug
Long Coiled Sync Cord (5ft, 15 ft) - PC Plug to Straight Mini Plug
Long Coiled Sync Cord (5ft) - ScrewLock PC Plug to Mini Plug
PC Plug Long Tip Tapered to Inline Mini Jack
ScrewLock PC Plug to Inline Mini Jack - Short with Safety Clip
ScrewLock PC Plug to RA Mini Plug 10 inches
Standard Heavyweight Sync Cord - PC Plug to Straight Mini Plug
Standard Lightweight 10 Inch PC Sync Cord
Sub-Mini Plug (Extra Small) for SkyPort Transmitter
Y Sync Cord With Extra ScrewLock PC Jack
Misc Adapters, Connectors, Cables
Aux Collar for ScrewLock PC plug
Adapters: Mini Plug to Mini Plug, Mini Plug to PC
Coiled Cables - 1/4 Inch and Mini
Dual Coiled Cable 6 Ft - 2 Mini Plugs to RJ11 or 4 Cond Mini Plug
Extendable Hand Trigger with 6 Foot Coiled Cord
FireWire 4 Pin M/M Cable
Hot Shoe to ScrewLock PC Plug for SkyPort
Hot Shoe to ScrewLock PC Plug - Upright Mtg
Leica Y Connector / Splitter for DMR Unit
Manual Tripper on 6 foot Coiled Cord - Custom HH Adapter
Manual Tripper Set Into Vinyl Hand Grip
Manual Tripper Set Into Plastic Box
Mini Connector Extension Cables
Mini-DIN Extension Cable
Mini-USB Extension Cable
Nikon Connecting Cord (SC-18) Modded to Mini Plug
RA Mini Plug to HH Male
Reduced Neck Sub-Mini Plug for SkyPort Transmitter
ScrewLock PC to Mini/Sub-Mini (Inline and RA) Rigid Adapter
SkyPort Receiver to Canon 580EX II - Manual Master Mode
Y-Adapter - Stock vs Custom
********************************************************************************
Purchase Info: Please Read
0 comments:
Post a Comment